Показать сообщение отдельно

Старый 25.03.2007, 16:32   #12
Местный
 
Аватар для gigabyte
 
gigabyte вне форума
Регистрация: 07.05.2006
Адрес: Str
Сообщений: 545
По умолчанию

Закаментировал. Теперь настройка личных параметров проходит нормально. В конфиг вроде всё занеслось. Это уже хорошо.
Набираю "adsl-start" - секунд 20-30 по экрану ползут точки (прогресс бар, видимо, местный) и ... "TIMED OUT". Лампочки на модеме при этом не мигают. Лог:

Код:
linux-7422:/opt/zyxel # ls
br2684ctl
linux-7422:/opt/zyxel # ./br2684ctl   -b   -c   0  -a   0.0.33
RFC1483/2684 bridge: Interface "nas0" created sucessfully
RFC1483/2684 bridge: Communicating over ATM 0.0.33, encapsulation: LLC
RFC1483/2684 bridge: Interface configured
linux-7422:/opt/zyxel # adsl-setup
Welcome to the Roaring Penguin ADSL client setup.  First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...

Looks good!  Now, please enter some information:

USER NAME

>>> Enter your PPPoE user name (default bxxxnxnx@sympatico.ca): xxxxxxx@mss

INTERFACE

>>> Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0): nas0

Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped.  If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses.  You may have some problems with demand-activated links.
>>> Enter the demand value (default no):

DNS

Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here:

PASSWORD

>>> Please enter your PPPoE password:
>>> Please re-enter your PPPoE password:

FIREWALLING

Please choose the firewall rules to use.  Note that these rules are
very basic.  You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security.  If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself.  Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc.  If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.

The firewall choices are:
0 - NONE: This script will not set any firewall rules.  You are responsible
          for ensuring the security of your machine.  You are STRONGLY
          recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
                for a LAN
>>> Choose a type of firewall (0-2): 1

** Summary of what you entered **

Ethernet Interface: nas0
User name:         xxxxxxxx@mss
Activate-on-demand: No
DNS:                Do not adjust
Firewalling:        STANDALONE

>>> Accept these settings and adjust configuration files (y/n)? y
Adjusting /etc/ppp/pppoe.conf
Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets
  (But first backing it up to /etc/ppp/pap-secrets-bak)
  (But first backing it up to /etc/ppp/chap-secrets-bak)



Congratulations, it should be all set up!

Type 'adsl-start' to bring up your ADSL link and 'adsl-stop' to bring
it down.  Type 'adsl-status' to see the link status.
linux-7422:/opt/zyxel # adsl-start
/usr/sbin/adsl-start: line 44: /bin/id: No such file or directory
adsl-start: You must be root to run this script
linux-7422:/opt/zyxel # adsl-start
................TIMED OUT
linux-7422:/opt/zyxel # adsl-start
................TIMED OUT
linux-7422:/opt/zyxel # adsl-setup
Welcome to the Roaring Penguin ADSL client setup.  First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...

Looks good!  Now, please enter some information:

USER NAME

>>> Enter your PPPoE user name (default xxxxxxxx@mss): xxxxxxxx@mss

INTERFACE

>>> Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default nas0): nas0

Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped.  If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses.  You may have some problems with demand-activated links.
>>> Enter the demand value (default no):

DNS

Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here:

PASSWORD

>>> Please enter your PPPoE password:
>>> Please re-enter your PPPoE password:

FIREWALLING

Please choose the firewall rules to use.  Note that these rules are
very basic.  You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security.  If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself.  Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc.  If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.

The firewall choices are:
0 - NONE: This script will not set any firewall rules.  You are responsible
          for ensuring the security of your machine.  You are STRONGLY
          recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
                for a LAN
>>> Choose a type of firewall (0-2): 1

** Summary of what you entered **

Ethernet Interface: nas0
User name:          xxxxxxxxx@mss
Activate-on-demand: No
DNS:                Do not adjust
Firewalling:        STANDALONE

>>> Accept these settings and adjust configuration files (y/n)? y
Adjusting /etc/ppp/pppoe.conf
Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets
  (But first backing it up to /etc/ppp/pap-secrets-bak)
  (But first backing it up to /etc/ppp/chap-secrets-bak)



Congratulations, it should be all set up!

Type 'adsl-start' to bring up your ADSL link and 'adsl-stop' to bring
it down.  Type 'adsl-status' to see the link status.
linux-7422:/opt/zyxel # adsl-start
................TIMED OUT
linux-7422:/opt/zyxel # ifconfig
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:190 errors:0 dropped:0 overruns:0 frame:0
          TX packets:190 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:12388 (12.0 Kb)  TX bytes:12388 (12.0 Kb)

linux-7422:/opt/zyxel # adsl-start
................TIMED OUT
Есть соображения на этот счёт?
__________________
"Левая стена - синий лед, правая - алый огонь. Нить между ними" - Лабиринт отражений.

Последний раз редактировалось gigabyte; 25.03.2007 в 16:48..
  Ответить с цитированием